Stuck bits on 11/73 Clearpoint 4MB memory - how to repair?

John Robertson jrr at flippers.com
Sat Feb 13 09:53:51 CST 2016


On 02/12/2016 6:55 PM, Jay Jaeger wrote:
> On 2/12/2016 5:32 PM, Jacob Ritorto wrote:
>> Hi,
>>      Seems I have bits 4 and 3 sticking on my Clearpoint QRAM-2-SAB-1 88b
>> 4MB memory in my pdp11/73.
>>
>>      Can anyone offer hints as to how to identify which component is broken
>> and how to go about repairing this?
>>
>>      It's the only memory board in this machine, so I guess the problem
>> might actually be a bus or processor board, right?  I have no other q-bus
>> memory to test with, so can't do swapping / process of elimination to be
>> sure.
>>
>>      Here's the manual:
>> http://www.arclightindustries.com/docs/Clearpoint-88B.pdf (which I probably
>> should add to manx or archive.org or something).
>>
>>      Here's a snippet of the VMJA diags run illustrating bits 4 and 3
>> sticking.  During the next VMJA run, all addresses were showing up as
>> errored instead of just the ones ending in xxx000xx, so I guess it's
>> getting worse!
>>
>> @173000g
>>
>>                                Starting system
>> BOOTING UP XXDP-XM EXTENDED MONITOR
>>
>> XXDP-XM EXTENDED MONITOR - XXDP V2.5
>> REVISION: F0
>> BOOTED FROM DL0
>> 124KW OF MEMORY
>> NON-UNIBUS SYSTEM
>>
>> RESTART ADDRESS: 152000
>> TYPE "H" FOR HELP !
>>
>> .R VMJA??
>> VMJAB0.BIC
>>
>>   CVMJAB0  ECC/PARITY MEMORY DIAGNOSTIC
>>     11/83 CACHE AVAILABLE
>> SWR = 000000  NEW = 000040
>>
>>
>>                 CSR MAP
>>
>> CSR     0 1 2 3 4 5 6 7 8 9 A B C D E F
>> MEMTYPE P
>>
>>
>> CSR NUMBER 0 CONTROLS TOO MANY BANKS
>>    2044K OF Q-BUS PARITY MEMORY
>>    2044K WORDS OF MEMORY TOTAL
>>
>>                          MEMORY CONFIGURATION MAP
>>                               16K WORD BANKS
>>                  1       2       3       4       5       6       7
>>          012345670123456701234567012345670123456701234567012345670123
>> ERRORS
>> MEMTYPE PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
>> CSR     000000000000000000000000000000000000000000000000000000000000
>> PROTECT PP
>>              1       1       1       1       1       1       1
>>              0       1       2       3       4       5       6
>>          456701234567012345670123456701234567012345670123456701234567
>> ERRORS
>> MEMTYPE PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
>> CSR     000000000000000000000000000000000000000000000000000000000000
>> PROTECT
>>          1
>>          7
>>          01234567
>> ERRORS
>> MEMTYPE PPPPPPPP
>> CSR     00000000
>> PROTECT
>> MEMORY DATA ERROR
>>    PC    BANK  VADD     PADD     GOOD     BAD     XOR  CSR  MTYP INT PAT
>>
>> 027606   10  060000  01000000  000010  000030  000020  0     P       27
>> 027606   10  060002  01000002  000010  000030  000020  0     P       27
>> 027606   10  060004  01000004  000010  000030  000020  0     P       27
>> 027606   10  060006  01000006  000010  000030  000020  0     P       27
>> 027606   10  060010  01000010  000010  000030  000020  0     P       27
> << SNIP >>
>
> Well clearly it is only affecting certain address bits - or the
> diagnostic would not run at all - note that it is starting at 010000000,
>   so that points to the memory, rather than the processor or bus, at
> least as a first approximation.  No guarantees, but I'd sure start with
> that as a working theory.
>
> Another sign: this is right at the boundary between two rows.
>
> If you can't find a schematic, you can use the address to identify the
> address lines on the bus (See Table 3, page 1-5), and trace them on the
> board to find the relevant row of chips.  Then use the bits the same way
> to identify the specific chips.
>
> If the chips are in sockets, you could always pull them one at a time to
> find the relevant place in the array, as well.
> ...
>
> Are you seeing the parity error light when this occurs?
>
> Anyway, once the relevant chip(s) are identified, if they are in sockets
> you can swap them with other bits or the same bits in other rows to
> confirm.  Otherwise you get to unsolder the suspects, and put in new ones.
>
> JRJ
>
An old trick we use for testing soldered in DRAM is to simply jam a 
known-to-be-good DRAM on top of the suspect one (legs bent in to make 
good contact). DRAM normally fail bits high and so putting a good one on 
top causes nothing different to happen if the suspect is good, but if 
the suspect is bad then the top DRAM will drive the output and your RAM 
test will pass.

Of course you wedge the good one on the suspect when the power is off. 
Unless you are in a rush, and willing to possibly kill your test DRAM.

As a side note - there appears to be an error message: "CSR NUMBER 0 
CONTROLS TOO MANY BANKS"  Or is that irrelevant? I know nothing about 
the PDP-11 test messages...

John :-#)#



More information about the cctalk mailing list