Question about an SGI Fuel issue / fuel sensors ( current - temp )

Mazzini Alessandro mazzinia at tin.it
Wed May 3 09:57:45 CDT 2017


Hello,

Since there are a lot of experts here ( I guess, at least ), I would like for an opinion / ideas / knowledge.

I've been told that the temperature sensors on Fuels are subject to get defective.
Is the same valid for current sensors ?

The question is due to this... I just got a Fuel donated to me, very kindly, that didn't turn on once I tried to. (the old owner didn't turn it on in a while, I was told)
I've connected to the L1 diagnostic serial port on the mb and ...
The env system prevents it from turning on for 2 reasons

1) XIO V12 bias with a value of 5.81 , considered too low
2) Odyssey temp fix at 93c at box turned off

But I managed to run env while the 30 seconds timer announcing the power down were running and... it shows that 12V and 12V IO are perfect with the psu "running" so... any idea if the xio v12 bias sensor is connected with the odyssey temp sensor and thus could be simply faulty.
I could do a test turning off env monitoring, but I would prefer to do it only after hearing opinions . given I don't know what kind of damages could happen if v12 bias is right , instead, and the system is brought up

Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.12
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
            5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.10
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.35
          2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.47
          1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.47
        5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.12
      3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
PIMM0 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
  Asterix SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.52
   Asterix CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.61
    PIMM0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    0.00
PIMM0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30
  PIMM0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.15
  XIO 12V bias      Fault  10%  10.80/ 13.20  20%   9.60/ 14.40    5.81
        XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    2.42
      XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    1.21
  XIO 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    1.60

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHAUST    Enabled          920         1129
FAN 1       HD    Enabled         1560         2229
FAN 2      PCI    Enabled         1120         1476
FAN 3    XIO 1    Enabled         1600         3869
FAN 4    XIO 2    Enabled         1600         3699
FAN 5       PS    Enabled         1600         1980

                           Advisory  Critical  Fault     Current
Description    State       Temp      Temp      Temp      Temp
-------------- ----------  --------  --------  --------  ---------
NODE 0            Enabled  60C/140F  65C/149F  70C/158F  20c/ 68F
NODE 1            Enabled  60C/140F  65C/149F  70C/158F  21c/ 69F
NODE 2            Enabled  60C/140F  65C/149F  70C/158F  20c/ 68F
PIMM              Enabled  60C/140F  65C/149F  70C/158F  20c/ 68F
ODYSSEY            Active  60C/140F  65C/149F  70C/158F  93c/199F
BEDROCK           Enabled  60C/140F  65C/149F  70C/158F  20c/ 68F



Alessandro



More information about the cctalk mailing list