Great, my VT52 is shot.

Mattis Lind mattislind at gmail.com
Sat Apr 18 14:00:59 CDT 2020


> We had a VT52 do something akin to that once back in the day... The tech
> we had that worked on this stuff said he had to fix something in the
> vertical refresh circuit to achieve vertical hold... My vague memories
> likely won't help you much, but this is quite distinctive and others of the
> group will be able to suggest things :)
>

Vertical hold implies that there is an oscillator that need to get into
hold or lock with an incoming signal.  There is none in a VT52 so that is
not possible. There is simply no way to adjust vertical hold in a VT52.

/Mattis


> Warner
>
>
>>
>> C
>>
>> On 4/18/2020 4:45 AM, Mattis Lind wrote:
>> > Hello Chris!
>> >
>> > Sorry that your trusty VT52 failed. But it shouldn't be too hard to
>> > repair it!
>> >
>> > I have successfully restored a VT52 (actually a VT50 with a brain
>> > transplant): http://www.datormuseum.se/home/dec-vt5x. My experience is
>> > that the capacitors were in good shape. Especially the bigger filter
>> > capacitor. I think that DEC used great quality capacitors.
>> >
>> > It is always a good idea to check the voltages so that they are within
>> > the spec. But it should not be necessary to replace all the capacitors
>> > in my opinion.
>> >
>> > The VT52 is a quite interesting design with a very simplistic CPU built
>> > from TTL components and a microprogram that has 1024 by 8 bits. Most of
>> > the operations inside it is controlled from this program. In mine the
>> > sockets for the mikroprogram were bad which meant that it failed to do
>> > anything. Then I had a couple of gates that were bad.
>> >
>> > Den tors 16 apr. 2020 kl 23:07 skrev Chris Zach via cctalk
>> > <cctalk at classiccmp.org <mailto:cctalk at classiccmp.org>>:
>> >
>> >     Wonderful: A few weeks ago I forgot to turn off my VT52 and left it
>> >     running for a day or two. Now the screen is filled with snow and it
>> >     looks like the text is all over the place horozontally.
>> >
>> >
>> > It would be great to have a picture since it could give some hints on
>> > what is wrong with it. My understanding is that the scan is working
>> both
>> > horizontally and vertically. Otherwise you would only have a straight
>> > line. Unlike many common CRTs this CRT circuitry has no oscillator in
>> it
>> > that creates a picture without input. And since the horisontal
>> > deflection circuit also creates the high voltage there would be no
>> > picture at all unless the horisontal signal is there.
>> >
>> > This means that the two control boards in the bottom creates some kind
>> > of horisontal and vertical signals. These signals comes from a simple
>> > divider chain. There could be some kind of problem in the divider
>> chain.
>> > But then it would be more likely to not work at all if one of the
>> > counters are bad. But it is a good idea to check the H and V signal som
>> > they are inline with the spec. Around 15kHz and 60 or 50 Hz
>> respectively.
>> >
>> > Since I haven't seen how the output looks like I speculating a bit. It
>> > could be the case that the divider chain is correct but the video
>> signal
>> > is not generated in sync with the divider chain. Then the characters
>> > would end up all over the place on screen.
>> >
>> > There is a flip-flip, made out of a 7400 (E16) and 74H10 (E14) that is
>> > the video flip-flop. It controls when the screen is rendered. It might
>> > be the case it could cause your problem. I think it is a  good idea to
>> > check the signals around this flip-flop.
>> >
>> > I am always a bit skeptical towards 74Hxx. My impression is that they
>> > fail more often than standard 74xx.
>> >
>> > When I repaired my VT52 I made a quick circuit that created a composite
>> > video signal from the control board. The signal was fed into a standard
>> > CRT monitor which I had around.  I could then run the control boards
>> > flat on the bench to take measurements rather than assembling prior to
>> > each test. I thought that it was quite handy.
>> >
>> >
>> >     Any tips or thoughts on where to start looking to fix? The keyboard
>> >     seems to be working as does the RS232 input (the snow on the screen
>> >     changes when the pdp11 talks to it)
>> >
>> >
>> > This indicate that since you are using RS232 you have at least some
>> kind
>> > of voltage level on +12 V and -12 V since otherwise there would be no
>> > communication. And +5V is probably not that bad either. Since not much
>> > would operate in that case. Likewise the -5V is probably ok since the
>> > char rom would not work very well without the bias.
>> >
>> > Good luck with your repair!
>> >
>> > /Mattis
>> >
>> >
>> >     Thanks!
>> >     Chris
>> >
>>
>


More information about the cctech mailing list