bobsmithofd at gmail.com
Wed Jan 27 13:08:07 CST 2021
Actually, DMC and DQ11 both had V35 options and both would hit 1.5
(1.3 actual due to protocol overhead. The DP8/e supported v.35 also,
but I don't recall how fast I could get that to go. I had bell 301 and
303 modems in the lab in the mill, running back to back. THere are
some arcane bits in the synchronous line units that were used with the
KMC for autodin II V.35 and RS422, thanks to some guys at Univ of
Mancheter. they helped me with a chip (along with Nat Semi) that
replaced the transistors and bits on the DP8/e for V.35 aka current
On Tue, Jan 26, 2021 at 2:00 PM Paul Koning via cctalk
<cctalk at classiccmp.org> wrote:
> > On Jan 26, 2021, at 1:24 PM, Peter Coghlan via cctalk <cctalk at classiccmp.org> wrote:
> > I wrote:
> >>> The other option would be synchronous links, which would enable connections
> >>> to DMC11 or the like at speeds up to 1 Mb/s. But synchronous comm devices
> >>> that connect to modern computers aren't so easy to find, though I have seen
> >>> a few.
> >> Not what would be called modern these days but I managed to run across two
> >> MicroVAX 3100 machines with DST32/DHT32 synchronous serial interfaces in them
> >> plus two V.24 and one each of V.35 and X.21 cables that will plug into them.
> >> With some help from the people here, I managed to get the machines talking to
> >> each other using a null modem between the two V.24 cables. I also have two
> >> nearly identical syncronous modems, one with a V.35 interface and another with
> >> an X.21 interface but I have not managed to get these to talk to each other,
> >> probably because they can't be configured to match any of the speeds the
> >> DST32/DHT32 interfaces can do.
> > Forget I said anything. the DST32/DHT32 won't do anything like 1 Mb/s.
> > Why do you want to go so fast?
> 1 Mb/s is the top speed of the DMC with the coax local "integral modem" connection. I don't know if the real modem card could go that fast. Probably not; the top speed requires special microcode. But the DMR, with a faster engine, can do 1 Mb/s without trouble. I suspect that if you take the modem flavor of the DMR and manage to clock those signals at 1 MHz you can indeed send that fast. Of course, RS232 officially isn't rated anywhere near that high (9600 I think is the official limit). Other physical links like V.35 or RS422 were used at the time to go faster. In every case, you can usually get away with going well over the limit if the cables are short enough, and especially if the cables are better quality than the minimum. For example, the DMC/DMR local connection is specified to use triax, but it wouldn't surprise me at all if Cat 5 Ethernet twisted pair cable works just as well.
> The main question for new work is what people have out there to connect to. The only thing I have is a Pro. That has a comm port with a USART, which will do sync just fine but tops out at 9600 bps or so due to having a tiny FIFO. That's RS232. I have no DMC or DMR or anything else fast in my collection.
> Thanks for the pointer to the Z85C30. Nice chip but it costs more than an Arduino (!); I was thinking of a software-only solution if possible.
> Mattis, thanks! That's an implementation along the lines I was thinking. If yours can get close to 1 Mb/s, chances are one could get all the way there with the Arduino Itsy Bitsy M4, that's a 120 MHz ARM chip (Cortex M4). It has USB built-in. I'll study your code; that approach of using a fast loop for consistent reliable timing matches what I was thinking.
> DDCMP is a bit harder because it's normally full duplex. The framing is different but no harder, I think. And I was thinking of leaving the protocol state machine to the host, so the microcontroller would only do framing -- deliver completed good frames to the host without interpretation.
More information about the cctech