test-drb May 2000

test-drb@ccmp.vtda.org

172 participants
541 discussions

by foxvideo＠wincom.net

I have just been given the remains of a Mac IIcx, and would like to determine its condition without spending too much money. Does anyone know the pinouts of the 15 pin video connector? Thanks Charlie Fox Charles E. Fox Chas E. Fox Video Productions 793 Argyle Rd. Windsor N8Y 3J8 Ont. Canada email foxvideo(a)wincom.net Check out "The Old Walkerville Virtual Museum" at http://www.skyboom.com/foxvideo and Camcorder Kindergarten at http://www.chasfoxvideo.com

26 years

Wanted: Manual and/or switch settings for Intel iSBC-012CX memory card

by eric＠brouhaha.com

I recently was given some Intel iSBC-012CX memory cards. These are 512K ECC DRAM cards that support both Multibus and an auxilliary high speed memory bus on the P2 connector (iLBX?). There was also a version that omitted some components and didn't support the aux. bus; I think that was the iSBC-012C. There were also partially populated models with 128K and 256K capacity; I think those were designated iSBC-028C[X] and iSBC-056C[X]. Anyhow, I'm looking for a manual for these boards, or at least information on jumper settings. Multibus originally only supported a 1M address space, so two of these would fill it up. Later A20-A23 address lines were added, but they were put on the P2 connector. Thanks! Eric

26 years

*ping* dave mcguire

by mcguire＠neurotica.com

On May 22, Dave McGuire wrote: > On May 22, Bill Bradford wrote: > > Dave McGuire, please get in touch with me off-list.. > > Heyhey...reply to old mail coming right up... DAMMIT I HATE FORCED REPLY-TO'S ON MAILING LISTS. -Dave McGuire

26 years

*ping* dave mcguire

by mcguire＠neurotica.com

On May 22, Bill Bradford wrote: > Dave McGuire, please get in touch with me off-list.. Heyhey...reply to old mail coming right up... -Dave

26 years

Mate-n-lock connectors?

by pete＠dunnington.u-net.com

On May 21, 21:48, John Wilson wrote: > Does anyone know of a source for new Mate-n-lock connectors, the horrible > 8-pin nylon things that DEC used to use for everything? I'm specifically > looking for the female ones with PCB-mount pins. The prints I have in front > of me (for the G848 flip chip) say the housing is 1209340 and the pins are > 1209456, but those part #s aren't listed in the CAS pricelist (even if you > add 00 on the end and put hyphens in the appropriate places). > > Amp still uses the name "Mate-n-lock" for some of their current nasty nylon > connectors, but I couldn't find anything on their web site that had 0.200" > spacing and 8 pins in a row, and none of the regular electronics catalogs > seems to have anything that looks even remotely right. I don't remember seeing 8-in-a-row in the Commercial Mate-N-Lok range for a long time, but two-rows-of-4 still exists, as does most of the rest of the range. If you can't find it on their website, try emailing them -- I did that about a year ago for something, and got a very helpful response. Unfortunately, I can't find the email so I can't just give you the address, but I seem to remember it was easy to find from their search page. -- Pete Peter Turnbull Dept. of Computer Science University of York

26 years

*ping* dave mcguire

by mrbill＠mrbill.net

26 years

I need to make a cable

by pete＠dunnington.u-net.com

On May 21, 18:51, Wayne M. Smith wrote: > I need to make a keyboard cable for one of my Texas > Instruments Portable Professional Computers. It is a > proprietary format with a standard CPU keyboard > connector on one end and a PS/2 female connector on the > other. I have a keyboard cable from a Texas > Instruments Professional Computer, which has the CPU > connector (and a grid-type plug on the other end) and > is a five wire cable. I had hoped to splice a standard > PS/2 cable onto it, but upon opening one of these up I > see there are only 4 wires so I'm a wire short Yes, PS/2 only uses 4 wires: ------ 1 Data / 5 3 \ 2 (Reserved) | --- 1 | 3 Signal Ground | --- 2 | 4 Power +5V \ 6 4 / 5 Clock ------ 6 (Reserved) > My question is, does anyone know of a PS/2 type cable > that has connections to all 6 wires that I could splice > onto the keyboard cable I have? Some Sun and SGI cables use five or six. For example, an SGI keyboard cable for an Indigo uses pins 1-5, and early 4D series use all six. Some extension cables sold for mice may have more than 4, because some dual serial/PS2 mice use them. -- Pete Peter Turnbull Dept. of Computer Science University of York

26 years

exabyte tape unit

by ghldbrd＠ccp.com

Hello guys and gals, I have a quick question: I just procured an exabyte EXB8505ST and was wondering if any of you knew what tape it uses and what the capacity is in MB. Got this at a swap meet for the case, but if the drive is useable, I'll keep it together. Respond off-list to keep the clutter down. Kind regards -- Gary Hildebrand ghldbrd(a)ccp.com

26 years

Misc Avail : morrow hd manual

by cmcmanis＠mcmanis.com

I found an old Morrow HD-DMA manual (S-100 hard disk card I presume) if you want it, let me know and I'll mail it to you. --Chuck

26 years

exabyte tape unit

by mcguire＠neurotica.com

On May 21, Gary Hildebrand wrote: > I have a quick question: I just procured an exabyte EXB8505ST and was > wondering if any of you knew what tape it uses and what the capacity is in > MB. Got this at a swap meet for the case, but if the drive is useable, I'll > keep it together. Respond off-list to keep the clutter down. Wow, if you bought it for the case, you probably got it cheap. 8505 drives go for $100-150 nowadays. I use Sony QG-112m data-grade tapes in my 8505 drives. -Dave McGuire

26 years

← Newer
1
...
17
18
19
20
21
22
23
...
55
Older →

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb May 2000