12 Oct
2007
12 Oct
'07
5:47 p.m.
Manual says something about "dissonant piano
chord" - how is it
supposed
to sound like? One thing I've verified that without graphics card
the chord sounds the same.
It's an arpeggio of some sort, perhaps with a 7th. Haven't worked it
out.
Getting the boot-tune means that much of the computer is working
properly. Try pulling the graphics and reseating the memory and
processor module & memory and see what pops out on TTY0. It could be
bad graphics (had that happen once in an Indigo), in which case there
is a surfeit of XL/Express graphics boards around (I have an Extreme
that I haven't used for years).
Do you know what the hardware is? Another possibility is that someone
tried to upgrade the processor module beyond what the boot PROM could
support. Most of the time the machine will 'let it slide', but some
cause issues (especially if it's a R10k on a R4k board). If you don't
know for certain than describe: "module with a big aluminum heat sink
and a small portion of board exposed that has several SMD memory chips
on it" can localize it to one of 2 processor modules (R4400 in either
200MHz/2MB cache or R4400/250 with 2MB). Also give the IP number of the
main board (it's near the riser for the GIO/EISA cards), and the model
number on the back (CMNB007-something).
15 Oct
15 Oct
9:56 a.m.
On 1012T0847, Scott Quinn wrote:
Pulling out graphics didn't change anything. Removing the audio module
did: the error changed to the following one:
Exception: <vector=Normal>
Status register: 0x30004803<CU1,CU0,IM7,IM4,IPL=???,MODE=KERNEL,EXL,IE>
Cause register: 0xb000c000<BD,CE=3,IP8,IP7,EXC=INT>
Exception PC: 0x9fc36674, Exception RA: 0x9fc3667c
Interrupt exception
CPU Parity Error Interrupt
Local I/O interrupt register 2: 0xc8 <EISA,SLOT0,SLOT1>
CPU parity error register: 0x308<B3,MEM_PAR>
CPU parity error: address: 0x87fee88
NESTED EXCEPTION #1 at EPC: 9fc4b3b0; first exception at PC: 9fc36674
After that I replaced the memory with some spare SIMMs I had, put audio
and graphics back in and it seems to work. That is, it actually gets
to the boot menu. I didn't install IRIX yet, I have only 16MB of RAM.
I wonder why the original memory didn't work. It's IBM brand, marked
"11E8360BD-70 VJRX 32MB, 8M X 36 P". SIMMs from HP/9000 E25 don't work,
too, but that's expected.
Manual says
something about "dissonant piano chord" - how is it supposed
to sound like? One thing I've verified that without graphics card
the chord sounds the same.
It's an arpeggio of some sort, perhaps with a 7th. Haven't worked it out.
Getting the boot-tune means that much of the computer is working properly.
Try pulling the graphics and reseating the memory and processor module &
memory and see what pops out on TTY0. It could be bad graphics (had that
happen once in an Indigo), in which case there is a surfeit of XL/Express
graphics boards around (I have an Extreme that I haven't used for years). Do you know what the hardware is? Another possibility
is that someone tried
to upgrade the processor module beyond what the boot PROM could support.
Most of the time the machine will 'let it slide', but some cause issues
(especially if it's a R10k on a R4k board). If you don't know for certain
than describe: "module with a big aluminum heat sink and a small portion of
board exposed that has several SMD memory chips on it" can localize it to
one of 2 processor modules (R4400 in either 200MHz/2MB cache or R4400/250
with 2MB). Also give the IP number of the main board (it's near the riser
for the GIO/EISA cards), and the model number on the back
(CMNB007-something).
System: IP22
Processor: 200 Mhz R4400, with FPU
Primary I-cache size: 16 Kbytes
Primary D-cache size: 16 Kbytes
Secondary cache size: 2048 Kbytes
Memory size: 16 Mbytes
PROM Monitor SGI Version 5.3 Rev E IP22 Sep 28, 1995 (BE)
Model No: CMNB007Y100
--
If you cut off my head, what would I say? Me and my head, or me and my body?
18 Oct
18 Oct
9:43 a.m.
On Mon, 2007-10-15 at 09:56 +0200, Edward Tomasz Napierala wrote:
After that I replaced the memory with some spare SIMMs
I had, put audio
and graphics back in and it seems to work. That is, it actually gets
to the boot menu. I didn't install IRIX yet, I have only 16MB of RAM.
I wonder why the original memory didn't work. It's IBM brand, marked
"11E8360BD-70 VJRX 32MB, 8M X 36 P". SIMMs from HP/9000 E25 don't work,
too, but that's expected.
"Just Plain Broken"?
If you can put the SIMMs into a plain ordinary PC (not sure if you can),
then try running memtest86 on them and see what happens.
Gordon
6424
days inactive
6430
days old
2 comments
3 participants
participants (3)
-
compoobah＠valleyimplants.com -
gordonjcp＠gjcp.net -
trasz＠FreeBSD.org