test-drb

test-drb@ccmp.vtda.org

101090 discussions

by cz＠alembic.crystel.com

Ok, with the RX02 running I see that 50 of these disks from Solarex were formatted with the FD: driver which is probably the MXV21 controller. Since I don't have a 5.4 version of this driver and to be honest will not be putting the MXV11 controller online anytime soon I'm offering these disks for free. So if you need 50 disks with various versions of RT11 and god knows what data on them or 50 frisbees let me know and they're yours for the cost of shipping. I need to either pitch these things or give them away. Thanks! Chris

4 years, 11 months

Needed HP 918lx computer trim bezel!a nice one appreciated bit one needing painting or? better than none!Please advise !Ed Sharpe Archivist for SMECC

by couryhouse＠aol.com

Needed? HP 918lx computer? trim bezel!?a nice? one? appreciated? bit? one needing painting? or?? better? than none!Please? advise !?Ed Sharpe Archivist? for SMECC?

4 years, 11 months

Modifying a RXV21 for an 11/83

by cz＠alembic.crystel.com

So I found an RXV21 board in the pile of stuff here and popped it into my 83. Crashes the system. It's an M8029 D board, and I see from this site that you have to add a few traces and cut a few others to make it work on an 11/73 or better. http://www.chdickman.com/rx02/ I'll pop in an 11/23+ CPU just to test it, but is it really just putting in two wires on the top of the board and cutting a total of three traces? Looks simple enough... C

4 years, 11 months

Rod Coleman's personal history of founding, building & running SAGE

by lproven＠gmail.com

On Sun, 3 Jan 2021 at 03:53, Boris Gimbarzevsky <boris at summitclinic.com> wrote: > > Ran into 68000 processor for > first time in 1986 when my father bought a 512 K > Mac and couldn't believe performance of this CPU It is odd. I had read of it, of course, but for me the revelation was getting an Acorn Archimedes in 1989, with an 8MHz ARM2, and seeing it blast past benchmarks of ~8MHz 68K machines such as the Amiga 500 or Atari 512 ST. It was about 4x faster, I believe. For me -- being a bit too young for the early days of the 68K family -- it was not a performance chip, but more about its ability to have lots of flat memory, unlike the crippled Intel chips that IBM used. > Weird that Rod Coleman had 68000 > instruction set associated with IBM 370 whereas > to me it was very PDP-11 like I've heard that before, yes,. and never the IBM comparison. I suppose it is a matter of what you're more familiar with. > Thanks for the link as didn't realize 68000 was > used for home systems before I ran into Mac. Sinclair's QL used a 68008 and was launched some weeks before the Mac. Of course Apple's own Lisa was before the Mac, too. Very soon after came the Amiga and ST -- the "Jackintosh", "power without the price." -- Liam Proven ? Profile: https://about.me/liamproven Email: lproven at cix.co.uk ? gMail/gTalk/gHangouts: lproven at gmail.com Twitter/Facebook/LinkedIn/Flickr: lproven ? Skype: liamproven UK: +44 7939-087884 ? ?R (+ WhatsApp/Telegram/Signal): +420 702 829 053

4 years, 11 months

DEC Pro operating systems and MFM emulator

by paulkoning＠comcast.net

The question was asked (I misplaced the note) if the OS images that are on the Xhomer website work with David Gesswein's MFM emulator on real hardware. You can turn these into emulator data files, provided you have the latest ext2emu tool that's part of David's software (as of 1/19/2021). The format needed is "Elektronika_85" which is the Pro format, called that because it was first added to the emulator as the format found on the Russian bootleg copy of the Pro of that name. Results, on my Pro 380: 1. P/OS 3.2: works. 2. Venix: panic at boot, "Bad access number". That doesn't mean anything to me. I wonder if the issue is that Venix doesn't support the 380. 3. RT-11 5.3: works. For grins I tried a smaller interleave factor than the default 5:1, since it seems reasonable that this should make things go faster on the Pro 380, given that its CPU is about 4x the speed of the one in the Pro 350. Somewhat to my surprise this isn't the case; the performance indicates that at 4:1 or smaller interleave the software misses the next sector and has to wait for another revolution. paul

4 years, 11 months

HP 3000, APL\3000, the HP 2641A APL Display Station, and stuff.

by gavin＠learn.bio

As some people here are aware, I have spent probably too much time this summer hacking on J. David Bryan's excellent Classic HP 3000 simulator and trying to build up the ultimate classic 1980s HP 3000 system (virtually speaking). I started with the MPE V/R KIT that's widely available and expanded that into a 5x120MB HP 7925 disc system and configured things like the system directory size and all the system tables to make a fully functional multi-user server. I then set about collecting as much old MPE software as I could find, which included Keven Miller's collection of the old Contributed Software Library tapes which were conveniently available in SIMH format. This is a huge trove of cool stuff including most of the classic mini/mainframe games (Dungeon, Warp, Advent, etc., etc.) and even a little game called DRAGONS that was written in 1980 by a guy named Bruce Nesmith when he was in college and he used it to get a job at TSR and went on to write parts of many classic D&D products and eventually landed at Bethesda where among other things he was the lead designer for another little game called The Elder Scrolls V: Skyrim. I was able to track Bruce down and give him a copy of the system with his 40 year old game running on it. The CSL tapes also include other amazing goodies that people developed and gave away over the years, including a FORTH and LISP, as well as most of the system and utility programs that people used to run their 3000 shops. It's quite fun to explore. I was curious how far we could push the 3000 simulator, so I hacked all the memory bank registers to be six bits instead of four bits, and we now have a simulated HP 3000 Series III that supports 8MB of memory, 4x more than any physical system ever did. I started trying to do the same thing for giant disc drives, but MPE turned out to have too much knowledge of what the supported disc models look like to make it practical. Bummer. Since I met my first HP 3000 in 1980 (40 years ago this month), people would talk about what was probably the most rare and exotic HP software subsystem ever produced, APL\3000. APL on the 3000 was a project started at HP Labs in Palo Alto in the early 1970s. They were likely motivated by the success IBM was having with mainframe APL timesharing services. This would be the first full APL implementation on a "small" (non-mainframe) computer. It would be the first APL with a compiler (and a byte-code virtual machine to execute the compiled code), it would include an additional new language APLGOL (APL with ALGOL like structured control statements), and it managed to support APL workspaces of unlimited size through a clever set of system CPU microcode extensions that provided a flat 32-bit addressing capability (on a 16-bit machine where every other language was limited to a 64KB data segment). Because APL required these extra special CPU instructions that you got as a set of ROM chips when you bought the $15,000 APL\3000, and because APL ultimately failed as a product (another story in itself) and thus HP never implemented these instructions on their later HP 3000 models, I never saw it run on a real HP 3000, but over the years we talked about wouldn't it be cool to find a way to get APL running again. With assistance and moral support from Stan Sieler and Frank McConnell and others, I was ultimately able to reverse-engineer the behavior of the undocumented ten magic APL CPU instructions needed to get it to run and implement them as part of the MPE unimplemented instruction trap and now APL\3000 runs again for the first time in ~35 years. Somewhat ironically, this implementation method could have been used back in 1980 as I didn't actually end up changing the hardware simulation code at all, and it should also run (if a bit slowly) on any physical classic architecture 3000. So that was cool and all, but what is APL without all the weird overstruck characters and whatnot? APL\3000 supports the use of plain ASCII terminals through blecherous trigraphs like "QD for the APL quad character, but this is hardly satisfying. So the quest was on to find a solution. Back in 1976 when APL\3000 was released, there was a companion HP terminal in the 264x line, the HP 2641A APL Display Station, which was basically an HP 2645A with special firmware and APL character set ROMs that supported all the APL special characters as well as overstrikes (the terminal would take X<backspace>Y and lookup to see if it had a character to represent Y overstriking X and if so it would show that on the display, and if that got transmitted to the host it would convert it back into the original three character overstriking sequence). I briefly looked into the idea of hacking QCTerm or Putty or something, but then I found out from Curious Chris that an HP 2645A emulator already existed in the MAME emulator system! Since the '41 is basically just a '45 with modified firmware, and Bitsavers had both the character set ROMs as well as the firmware ROMs from a '41, this sounded like it might be easy! There was a snag however in that the firmware ROM images that were allegedly from a '41 turned out to actually be from an ordinary '45. But we did have the character sets and one of the ROMs from the second CTL PCA. I put out a call on the Vintage HP list to see if anyone might possibly have a lead on an actual HP 2641A, and Kyle Owen responded that not only did he have one he could also dump the ROMs for us. So a few days and a few hacks to F. Ulivi's MAME hp2645 driver later we now have a functioning MAME HP 2641A terminal emulation, so you can experience APL\3000 in all its original glory. I bundled up a somewhat stripped down MAME along with my turnkey 3000 setup so both emulated HP terminals are just a couple clicks away. So that's how I spent my summer vacation (who am I kidding, it's pretty much all vacation these days). It has been a lot of fun revisiting all this old 3000 stuff as well as the numerous people I talked to along the way including some of those who were around at APL\3000's birth (before my time). It was rather a lot of work so I'd like to feel it might be useful to someone in the future who is digging into this part of history. Because of all the usual reasons, I don't plan on hosting it permanently until and unless we maybe someday get the licensing worked out (the 50th anniversary of the HP 3000 will be in a couple years so maybe people will get interested again then) but I will offer it up here to my fellow computer history nuts if you want to help ensure that it doesn't vanish if I get run over by a bus or something :) This is a simulated HP 3000 Series III (circa 1980) running MPE V/R (circa 1986) with 8MB of memory, all the language subsystems (APL, BASIC, BASICOMP, RPG, FORTRAN (66), SPL, PASCAL, COBOL (68), COBOL II (74)), 20 years of users group contributed software, many classic historical computer games, etc. Software archaeologists can get lost in here for years. Oh, and thanks to Dave Elward, the HP 2000 Timesharing BASIC contributed library is even included (kinda sorta converted to MPE BASIC) for good measure. This is a streamlined turnkey edition that's ready to run out of the box with no assembly required (all batteries are included). Currently, I only provide executables for Windows (sorry) but am in the process of getting the 3000 simulator changes (for large memory support) and the new MAME hp2641 driver back upstream. Instructions and further details can be found in the README.txt hint book for this adventure. 94MB Google Drive link: https://drive.google.com/file/d/1bmXvHkBLbUeLAid73EJ4H1yQ2uwXQuRu Gavin P.S. I'm giving a talk on the history of APL\3000 and its resurrection to the ACM APLBUG group in a couple weeks. If anyone is interested I can provide more details when I have them.

4 years, 11 months

cc:Mail

by tomas＠basun.net

Hi all, I don't suppose there is anybody here who has `Lotus cc:Mail Router Release 5.1' ? /Tomas

4 years, 11 months

Got DSM-11 running, any manuals online?

by cz＠alembic.crystel.com

Well, with Dave's help we got the DSM-11 disk to boot on SIMH. Oddly enough SIMH seems to read a raw RQDX1/2 disk pretty well. sim> attach rq0 dsm.dsk sim> set cpu 11/73,1m Disabling RK Disabling HK Disabling TM sim> boot rq0 Booting DSM-11... DSM-11 Version 3.0A Now running the baseline system. <DKHER>:1 G ^STU Exit DSM-11 Version 3.0A Device #1 UCI: Exit DSM-11 Version 3.0A Device #1 UCI: ? <NOUCI>:0 Exit The problem is I don't remember how to use it anymore. Is there a PDF of the DSM-11 manual anywhere? I think this was a clean install, but I'd like to check it for data before putting it into archives. Also which archive would be best for it? CZ

4 years, 11 months

DEC Pro 3xx archives

by paulkoning＠comcast.net

I recently ran into an archive of various Pro 300 items, mostly from DECUS I believe. That includes a full P/OS 3.2 distribution including (!) DECnet/Pro if I saw that right. It's at ftp://ftp.update.uu.se/pub/professional/ What makes things somewhat painful is that it's LHA compressed Teledisk images, which is an ancient DOS based floppy imaging tool. The instructions say to run Teledisk on a DOS system with a 5.25 inch floppy drive to write the images to RX50 floppies, which can then be used. If you don't have DOS handy, or would rather get floppy image files for use with Xhomer, this can work but it's a bit painful. I found there's a simpler way. 1. Decompress the LHA files. On a Mac, the unarchiver (I think that comes with the OS?) handles that format. On other operating systems, I assume it's equally straightforward to find a tool that handles this. You now have a pile of *.TD0 files, which are the TeleDisk format files. 2. From http://www.seasip.info/Unix/LibDsk/ install LibDsk 1.5 (not 1.4). 3. Use the dsktrans tool you got from step 2 to convert each *.TD0 file to a raw image, like this: dsktrans -otype raw PRO177/177-21.TD0 proinstallv32.dsk "raw" format means a straight sector dump in physical order; this is the format expected by xHomer. If for any reason you want a logical order image, for example to give to the SIMH "rq" device that emulates an RQDXn controller, you'll need a tool that reorders things. I have one in my RSTS file system tool "flx" (V3 in Python, not the earlier 2.6 in C), "rx50.py". I can supply more details if needed. paul

4 years, 11 months

<Plug> HP1000 A990 Servers

by jesse＠cypress-tech.com

I have a few of these A990 boxes. They are complete with memory, internal disk & DAT, & any 1000 interface you could possibly need. They are the smaller 14-slot Micro boxes so a small footprint. I'm doing a few of them for $1,300.00 each.. If anyone wants one, let me know. The ebay link is below and feel free to ask me any questions about them. www.ebay.com/itm/383752338096 <www.ebay.com/itm/383752338096> Thanks Jesse Cypress Tech

4 years, 11 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb