test-drb

test-drb@ccmp.vtda.org

101090 discussions

by gordon+cctalk＠drogon.net

I'm moving soon and need to down-size a little, so selling off my PDP-8/a. It has 16KW core and is in full working order. It has the serial IO board which I think was standard in the 8/a anyway. It's a 3-card system plus the 2 x 8KW core boards. Also included is a Vincent Slyngstad memory/rtc expansion board - not built up, so full kit form that I've not been able to assemble yet. ?1000 ono. https://unicorn.drogon.net/IMG_20210305_150415.jpg boards: https://unicorn.drogon.net/IMG_20180126_181135.jpg https://unicorn.drogon.net/IMG_20180126_181115.jpg https://unicorn.drogon.net/IMG_20180126_171659.jpg I'm based in Devon. Buyer collect (if you want to see it working) else I can make a short video and may be able to take it a little way up or down the A38/M5. Thanks, Gordon

4 years, 8 months

Looking for the numeric pad "1" key on VT-100 vintage keyboard

by cramcram＠gmail.com

Does anyone out there have a "1" key (the one in the numeric keypad, not the 1 / ! key) that they are willing to sell: me? I saw a couple of partial keyboards go fairly cheap on ePay a couple of months ago but didn't see it until it was sold. Thanks, Marc Howard

4 years, 8 months

Intellec MCS-8 8008 monitor program ROM files

by roelof_klaas＠yahoo.com

Hello everyone, Does anyone have the?Intellec MCS-8 8008 system monitor ROM files? According to the Intellec MCS-8 manual the System Monitor is contained in five 1702A PROMs.My ROMs have a disk loader, but the disks system is long gone... Any papertape software is also welcome for this machine! Thanks in advance!Regards, Roland Huisman

4 years, 8 months

SPARCengine CP1200

by rp＠servium.ch

I just acquired a Sun SPARCengine CP1200. To my knowledge the CP1200 is the only 32bit SPARC with a PCI bus, which makes it pretty cool. It was also extremely unpopular, because who wants a 100MHz MicroSPARC IIep when you can have a SPARCengine CP1500 with a 270MHz UltraSPARC IIi (they were released at the same time, and I suspect the cost difference wasn't all that much). Would anyone know where I can find a Sun PROM image? mine has a VxWorks ROM, but I'd rather run Solaris on it. I've searched everywhere, and couldn't find anything. Most "usual" places (e.g. the FE handbook) barely acknowledge its existence if at all. AFAIK this predates field upgradeable flash PROMs, so it's not hidden in a patch somewhere. thanks Rico

4 years, 8 months

Searching for Elevated socket

by brain＠jbrain.com

IN my continuing Digitalker saga, I did find a couple not horribly priced Digitalker ICs online and purchased them.? As one arrived, I found that my original IC was actually OK, but the cable from the computer to the device has issues. I've traced it to what looks like a heavy duty 16 pin IC socket on the board that plugs into the computer, and into which a 16 pin 2x8 .3" DIP IDC header plugs into (with the IDC cable going to another such header, which plugs into a similar socket on the main synthesizer PCB). The socket has the same basic footprint as a normal 2x8 16 pin .3" IC socket, but it's much heavier duty.? I could replace with a simple leaf socket, but would prefer to find a direct replacement. Though I am sure other manufacturers sold similar, I find that Aries sells that I need.? It's an Aries 16-8430-10 <http://www.beckwithelectronics.com/ARIES/16-8430-10.htm> (or could be an Aries 16-8480-10 <http://www.beckwithelectronics.com/ARIES/16-8480-10.htm>) elevated IC socket.? The link below shows the units: http://www.beckwithelectronics.com/ARIES/8xxx.htm Digikey has the 14 pin version in stock, but no 16 pin ones, and neither does Mouser.? I'll keep searching, but they are very expensive and I'm not sure I need 40 of them (minimum Digikey order). Thus, I am wondering if someone on list has 1 or 2 they might be interested in selling for the cause. The good news is that I was able to get the connection to work, and now the unit operates as designed. Still, I do not trust the socket. Jim -- Jim Brain brain at jbrain.com www.jbrain.com

4 years, 8 months

Massbus - was: Re: VAX 11/750

by jnc＠mercury.lcs.mit.edu

> From: Paul Koning > There's a good reason why the big disks on many DEC machines were Massbus > devices until MSCP arrived. It's quite clear on Unibus PDP-11s, which > needed Massbus both for speed and for a cleaner answer to more-than-18 > bit addressing. I follow the first sentence, but I'm confused by the second, especially "a cleaner answer to more-than-18 bit addressing". The UNIBUS MASSBUS controller/adapter, the RH11, only has 18-bit addressing on the main memory side. It does have more than 18-bit addressing on the device side, but so does the RP11 (sort of). Are you thinking of the RH70? That does have access to more than 2^18 bytes of main memory, but that's because it connects to the -11/70 memory bus (as well as the UNIBUS, which is only used for control, not data). Similar questions about the speed point; passing data through an RH11 doesn't increase the speed of the UNIBUS? Yes, the RH70 is faster, but that's because of its connection to the -11/70 memory bus. Noel

4 years, 8 months

PDP-8/I vs 8/E EAE

by kylevowen＠gmail.com

Has anyone noticed a difference in DVI overflow behavior on the PDP-8/I EAE versus the PDP-8/E EAE? The 8/E EAE claims to be 8/I compatible in Mode A, and I think I agree, for the most part. At least, it's compatible for the parts that matter. When a DVI instruction results in overflow, the EAE immediately returns with the link set. The results in AC and MQ seem to have no relevance, but they appear to differ between the 8/E and 8/I. For instance, running the 8/I MUY/DVI diagnostics under SimH fails due to the following: sim> lo maindec/maindec-8i-d0ba-pb.bin sim> d sr 40 sim> g 201 DIVERR L C(AC) C(MQ) C(MB) PROB 0 000000000000 000000000000 000000000000 GOOD 1 111111111111 000000000000 000000000000 BAD 1 000000000000 000000000001 000000000000 SCA 000000000000 HALT instruction, PC: 01512 (JMP I 1506) The link is set, but obviously MQ and AC do not match. Running the same diagnostic on an 8/I works fine. I can't imagine a scenario outside of diagnostics where this behavior would impact the software, but it does seem curious nevertheless that the DVI approach to handling overflow differs slightly between EAEs on the 8/I and 8/E. Kyle

4 years, 8 months

DS20 Alpha System

by jwsmail＠jwsss.com

I've got rights to a fairly nice system located in St. Louis.? It has working streaming tapes as well as half inch, all working. It is on till this coming weekend. The full system is a single bay, I've been told is 7' tall on casters.? I won't let it be scrapped if possible, but I'd like it to go off the floor directly to someone interested and not have to use favors to get help having it moved out. It will be skinned of an addin UPS but otherwise disconnected and put to one side till it can be picked up. Told the location has dock high, but no word on how that is accessible or what type it is.? Might be able to move dock high to dock high anyway. Let me know if there's interest.? I will have to have possession of the drives, but will make sure the hardware that goes with them is kept.? I hope I can zero them and pass it along. Cabling will be boxed as appropriate and will be included. Let me know if you are interested, and pass it along.? I know it's a dual processor, but don't have other info right handy here. thanks Jim

4 years, 8 months

Any interest in a Floating Point Systems AP-120 array processor?

by boris＠summitclinic.com

That appears to be an earlier model of a similar system we had at UBC which could crunch arrays of FP numbers at 10 Mflops. Had it connected to an 11/44 and just recall doing some frantic programming mainly involving using minimal code as had to use memory management to allocate memory pages to get data into array processor and then fetch results. Realized at that time that a 56 Kb memory space was a bit limited for this type of work. Did FFT far faster than 11/23 (which took 1 second for 1024 points using DEC's code that shipped with MINC) but still had to do overnight runs to analyze a lot of our data. Likely have bad memories of that part of my programming career as we were under some rather tight deadlines to analyze data to get a few papers published and I much preferred writing in PDP11 assembler as very rarely had to deal with running out of memory issues with data acquisition code. Out of curiousity, decided to benchmark one of my old, really cheap PC laptops that got in 2010 and it managed 30 Mflops using double precision arithmetic. 10 Mflop performance no longer as impressive as it used to be. >I picked this up a number of years ago for reasons that entirely escape >me. It's certainly neat, but I don't see myself ever actually using it and >it's large and heavy. > >Documented here: >http://bitsavers.trailing-edge.com/pdf/fps/7259-02_AP-120B_procHbk.pdf > >Mine appears to have a DEC-style interface but I'm unsure what it talks to >on the DEC side of things. > >I can take pictures if there's interest, but it's fairly nondescript, just >a large white box with rack-mount ears and a small panel with some switches >on it. > >It's in the Seattle area if anyone wants it, and it's free! Shipping is... >not something I really want to think about right now. > >- Josh

4 years, 8 months

Any interest in RLX blade servers

by julf＠julf.com

RLX Technologies pioneered the blade server concept between 1999 and 2005 (when they got acquired by HP). I have two of their early RLX 24 blade enclosures, one fully populated with 24 transmeta-based processor blades, and the other with 19 blades. Julf

4 years, 8 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb